Skip to content

How to Calculate Voltage Drop Step by Step

Up to date as of 18 November 2026

The sum is short: voltage drop equals current times resistance. The only tricky part is finding the cable's resistance, and that comes from three things you can look up or measure.1

Step 1: Know the current

Current is measured in amps. Check the label or manual of the light, fridge or charger. If a device lists watts, divide watts by volts to get amps. Victron's example does exactly that: a 2400W load at 12V makes a current of 200A.2

Step 2: Use the round-trip length

Measure the cable from the battery to the device. Then double it, because current goes out and comes back. Victron's own table uses the total cable length, the positive cable plus the negative cable.3

If the device is 5 metres from the battery, the total is 10 metres.3 The round-trip length page goes into this more.

Step 3: Work out the resistance

Resistance goes up with length and down with thickness. Wikipedia puts it this way: the resistance of a given element is proportional to the length, but inversely proportional to the cross-sectional area.4

For a copper cable the sum is: resistance in ohms equals 0.017 times the length in metres, divided by the size in mm².2

That 0.017 is copper's resistivity. Victron's book writes it as 1.7 × 10 to the power of minus 8, for sizes in square metres. Cable sizes come in square millimetres, so 0.017 is easier to use and gives the same answer.2

Step 4: Multiply by the current

Wikipedia says Ohm's law can be used to find DC voltage drop by multiplying current times resistance.1

The voltage drop sumFind the round-trip lengthWork out the cable's resistanceMultiply resistance by the currentCompare the volts lost with 12
Work from cable size to resistance, then to volts lost.

A worked example

Take a 12V device that draws 10 amps, sitting 5 metres from the battery on a 4 mm² copper cable. The sums use the figures from the steps above.2

  1. Round-trip length: 5 + 5 = 10 metres.3
  2. Resistance: 0.017 × 10 ÷ 4 = 0.0425 ohms.2
  3. Voltage drop: 10 amps × 0.0425 ohms = 0.425 volts.1
  4. As a share of the battery's 12 volts: 0.425 ÷ 12 is about 3.5 per cent.1

That's a rough result for a straight copper run. It ignores the join at each end, which adds a little more resistance.2

Check your answer another way

Victron publishes a table of the maximum current for standard cable sizes. It's based on a drop of 0.259 volts and the total cable length. For a 4 mm² cable, the table gives 6 amps at up to 10 metres.3

Scale it up and the answer agrees with the sum above. A 10 amp load is about 1.7 times the table's 6 amps. So it loses about 1.7 times the 0.259 volts, roughly 0.43 volts. That agrees with the 0.425 volt sum above. The scaling is this site's own arithmetic, from Victron's 6 amp and 0.259 volt figures.3

Victron also offers a free app. You enter the voltage, cable length, current and cable cross-section, and it works out the drop over both cables.3

What changes the answer

  • A longer run raises resistance, so the drop grows.2
  • A thicker cable lowers resistance, so the drop shrinks.2
  • More current means more volts lost for the same cable.1
  • Temperature and the cable's material also play a part.1

Once you have the drop, compare it with the usual limits. To skip the sum each time, a cable size chart does it for you.

Cited material

  1. Voltage drop, Wikipedia
  2. Wiring Unlimited: Theory (current, cable resistance and voltage drop), Victron Energy
  3. Wiring Unlimited: DC wiring (cable selection), Victron Energy
  4. Electrical resistivity and conductivity, Wikipedia